That's Impressive! (and Counterintuitive)

The first receipt on the right shows the results of my new set up using two Electrolyzers connected in series with one teaspoon of Baking Soda in each , the Oxygen Sensor out of the system altogether, and the MAP Sensor Enhancer working perfectly - and yet my mileage stinks! (comparatively that is) If you've been following along you will know that 21.89 is pretty much what my car gets without enhancement of any kind. - And some of the mileage is on the highway...

The second receipt however (on the left) shows something very different at 27.41 MPG - it shows my best mileage ever!

Yippie!

So the question is what's different? Well it's something pretty simple and still makes my head hurt to think about it. It's the setting on the MAP Enhancer! - and this is the counterintuitive part: following directions I set the enhancer by leaning it out until the car stalled out and then came back a quarter turn, but that quarter turn in my mind was a quarter of the way back from where the car stopped chugging - but that was wrong. It wasn't enough. After I saw the crummy results I turned the rheostat back even further. To put this in perspective: the car was chugging at 30 - I turned it back to 20 which resulted in zero gain as shown on the Exxon receipt. After that fill up I turned it back to 10 and gained significantly! In other words trying to run too lean resulted in worse mileage.

Now let me be clear that this is not information that did not have in the first place through my interaction with Vernon Minton at HHO Development. He originally sent me instructions that included the following information:

MAXIMIZE BENEFITS
MAXIMIZE BENEFITS
One recent set of road tests (6-16-07) averaged 52.4% better mileage. But, tests from a week earlier on the same car averaged
only 24.5%. Actually, 22% if you discount idling. WHY such great difference?
The secret of the BIG DIFFERENCE between the two test groups: The later and more successful one got MORE THAN DOUBLE the average gain because the MPG was not dialed to near choke point. It was about 1/4 tum closer to factory setting!
Don't overwork the engine by leaning it too much - play around until you find the PERFECT BALANCE point.

Now did I listen to that? - Well I tried but I couldn't bring myself to believe that less is more - however as it turns out - that is exactly the case. The image of the Enhancer above is the one currently in my car. The setting that you are looking at is my current setting which does not mean that it is the setting that your car should be at, but learn by my experience - again the car bucked at the 30 setting - would run at 20 no problem (but without gain in MPG) and really gets the job done at 10... There ya' go.

Just FYI - I've just added a 1/4 teaspoon of Baking Soda to the Electrolyzers. Onward and upward:-)

See ya' next time.

Same Day New Post - Gas Shenanigans

Hey I found the best gas price in town! Uh well no I didn't 'cause once I was in the station I discovered that there was a dollar surcharge because I dared to use my Debit Card to pay. But hey I figured I was already in the place and I wanted to get gas and I know already that I would never go back to a place that would play games like that. I didn't need that much gas anyway... I filled up and paid and because I'm always curious to see how much I'm putting in the tank I couldn't help but notice that the amount of gallons on the receipt was more than the amount shown on the pump. This receipt is a bit hard to read but it does show 3.434 gallons when what I actually got was 3.195 gallons. It's not much but I noticed and when I asked the attendant/owner what was going on he told me that the extra dollar was represented as fuel! Can this be legal? Anyway it's the only reason that I bothered to put this receipt up for viewing since it only partially representing a w4g result. I went about 35 miles using nothing but the Oxygen Spacer after which I installed the new stuff and disconnected the Oxygen Sensor from the system altogether. So 23.09 MPG is the result but that really tells nothing at all, so let's not focus on it... okay? I'll be back in a few days to spill the beans.

On the Road Again

Well yesterday was the big day. I installed the newest of the new MAP Enhancer's and took the opportunity to essentially start all over again with my set up. The first thing I did was to pull the negative cable from the battery so that the computer could reset while I worked on everything. Although I have mentioned that I've been told that removing both cables and touching them together would do the same trick - I figure that since I have the time to use the tried and true "traditional" method - why not?

The phenomenon of the nearly magnetic attraction of this technology became apparent within about 4 minutes of the time I popped the hood - I was joined by three guys, a woman and a Cocker Spaniel from the neighborhood. Everyone wants to know what's going on with the gadgets in my car. Of course this comes along with people who think that they know stuff like how to connect wires. I had to explain several times to one of my pals that I was connecting the two units in series, and that I really meant to do it that way...-)

The image above shows the new installation in action. That little crate thing I put the Electrolyzers in came from the Dollar Store (although it cost like $3.00) and gave them a pretty stable platform to put them on after I took a pair of cutters to it to give me room for the air intake duct leading to my injector. I'm placing another closeup image here since I'm pretty proud of myself at this moment. You'll see lots of indications showing the Positive and Negative terminals since I didn't happen to have any red and black paint around (not that it did me all that much good when I had it before.

Here's a hint about putting the angle fitting(s) in the cap to accept the vacuum line(s): each end of the fitting has a kind of lip or barb around the edge making it very difficult to push through the hole. So take a pair of shears or a wire cutter and cut just above that lip and then push it through the hole. Ozzie's books show that a 1/4 inch nut is twisted down over that inner piece sticking downward through the cap. I found it much better to use a lock washer for the purpose to holding it firmly in place before sealing with Goop.

I must admit that felt exceptionally confident with what I was doing this time around in that I personally built my Electrolyzers. Not only that, but these Electrolyzers contain laser-cut and notched towers that I personally designed, 316L wire that I personally braided and lovingly wrapped on each one, and the laser-cut caps topping everything off were those that I produced as well. Each item attached to the cap was one that I personally attached and sealed with Goop. What I am saying here is that I know that these are exactly what they need to be. I am not relying on anyone else for the physical condition of these Electrolyzers. Why is that important to me? Have you read the earlier posts in this blog? Everything is important. Each small component, each procedure, each element is meant to be perfect in its own way. Does this mean that I can't goof? Again, I ask if you've read earlier posts:-) The thing is that I do learn from my mistakes. The last one cost me $60.00 and it was worth every nickel. If it had cost me $6000.00 I must admit I might feel differently. Nevertheless my lesson has been learned and I know to be careful with each and every part. The information in the Water4Gas books is meant to be our guide, but I'm pretty sure that I can't be the only one who thinks that I can go along and easily do what's been described, but doing it my own way (an example of this is that I tried other glues in place of Goop. Just FYI Gorilla Glue and Silicone do not work properly as sealers) and expect to get the described results. It's in my nature to explore the boundaries and expand beyond what I already know. The truth however is that it's important for me to know the basics before I move ahead with my brilliant ideas. Ozzie has provided an amazing blueprint for us, but that's a jumping off point and we all know it. My issue generally stems from thinking that I know everything before I really know it. Still all in all I'm having a blast. The progress I've made in understanding how my car works and what certain things are supposed to do is remarkable in just two months - especially considering that when I put my first Electrolyzer in the car I had to as my mechanic what the vacuum lines looked like. So far so good.

I'm going to head out and fill the tank so that I can get an accurate measurement on the results.

Life is Indeed Strange

As you know I've been going through every possible craziness as I move along in my quest for mileage. At this point I have a pretty clear understanding that my MAP Enhancer on the Highway setting somehow had a dead short. I also want to make this clear. I sent off a note to Mr. Minton, the man I purchased my Enhancer from and within an hour or so he called me on the phone. Again he demonstrates his integrity, and is sending a replacement. He will also pull the device I've been using apart so that he can find out what went wrong. As far as I can tell this could have happened to anyone. Nevertheless it's happened to me, and in the interests of telling everything - I feel obligated to tell this as well. To put this in perspective I recently sold 100 of the towers to one of my customers in North Carolina. I received a call from her and she told me that 34 of the towers would not go together without splitting. I immediately sent out replacements. She told me that it seemed as though some of the tower pieces were thicker than others and I wondered aloud how that could possibly be. Well as it turns out she was right! and for the very first time ever I was wrong:-) Can you believe it? - Seriously though, as it happens, when very large shipments of sheet Plexiglas come in they can be ever so slightly different in thickness, and that is exactly what happened - the towers that she received were partially made from one run of the sheets, and the rest from another. The point it is that weird things happen, and all we can do is make sure that no one suffers from those occurrences. I took care of the problem for her and Vernon is taking care of the problem for me. When we come together as people of honor there is no fault, no blame - only solutions.

Now about that receipt you're looking at above - I got 23.37 MPG without the Electrolyzer or the MAP Enhancer working! The only thing I had going for me was the Oxygen Sensor Spacer. The gain I've been getting for the last several fill-ups apparently is from that device alone. What a surprise that turns out to be - especially since, as I mentioned in an earlier post, the next move I intend to make once I install the new MAP Enhancer - is to remove the sensor from the system altogether - to allow the Enhancer to control the amount of gas being used. I still intend to do that and let the results fall where they may. We shall see. We shall see.

Attaching An Electrode Wrapped Tower to the Cap

I've been asked several times to post this video, so here it is.

I hope that it helps.

Again I want to reiterate I am not the expert in any of this. I am just a person learning about a new technology like the rest of you. Still, while I may not know everything that there is to know about HHO and Water4Gas technology it just happens that I am very knowledgeable about how things go together, how to solve difficult spacial problems, and how to make things happen in a logical sequence. One of my previous occupations was as a master art-mold maker. The trick in that task is to know how to look at an original work made of wood, clay, wax or whatever - revolve it in space three dimensionally in one's mind - imagine the desired end result of a finished work of bronze art - and then begin creation of the mold with that final image in mind. I guess that I just know how to make things work.

A Frank Analysis of The Problem

As it happens I have somehow been elected to represent all of those people who charge forward and get things wrong, and make mistakes, and have a need to find out how to come back from barriers that on the surface - point to failure, but on re-examination point to a greater wealth of knowledge than could be gained without the problem... (Unless of course someone else has done it for you:-) Anyway, I now know that the problem that I experienced the other day had nothing to do with the new MAP Enhancer. In that light I've created another of my little videos that shows pretty clearly what I did, where I went wrong, and obviously - what not to do.

Even though I now know the source of the problem I've not completely solved everything related to it. I know that the short in the system originally took place in the Electrolyzer, and I've made the correction by replacing it altogether, however somehow that short affected my Air Conditioner, and as I investigated further before finding the problem - has now caused additional problems with my radio. - I've scheduled an appointment with my mechanic tomorrow morning. Hopefully, it's not huge -but really I have no idea on what his findings will be. (I know that you all have your fingers crossed for me.) With any luck it will cost me enough to make me overly cautious in the future, but not so much that I'm freaking out.

BTW - you heard it right in the video - the melting temperature of Plexiglas is 270 F.

Also I want to mention one other thing here: one of my customers, a man I would now consider as a friend, Alan was doing a bit of experimenting one day last week, and came across something very important. He attached an Electrolyzer to a 12 volt battery, and fortunately for everyone involved - left it in the corner of his barn, and walked away from it intending to leave it on all night to see if it would continue to pump out HHO. When he returned a few hours later he discovered that it had BLOWN UP! - Never, never, never connect the Electrolyzer without having the generated gas drawn off by a vacuum. Alan made this mistake for the rest of us. We owe him our sincere thanks. Please don't duplicate it. Stay safe.

I spoke with someone yesterday who is very knowledgeable in this area, and he mentioned something else very important to all of us, and that is that right now this community is sort of flying under the radar, but if it ever occurs that there is a really bad accident involving HHO and water4gas - that flight will be over. I encourage everyone to be extremely careful - don't play with HHO gas anymore than you would play with a live high voltage electrical line.

'Nuff said, right? Now, let's go change the world.

Now that I've Achieved Consistancy I Also Have a New Problem

As much as I'd like to deliver good news all of the time it's jut not possible...
I have another issue that came up for me this afternoon and I'm trying to figure it out, and see how it all relates. Here's the scenario: Georgina and I have driven into Manhattan to deliver some things to a friend who happens to be a shut-in recovering from an operation. It's hot and muggy. The AC is on. So anyway I get on the FDR Drive and switch the MAP Enhancer over from "City" to "Highway" at which point the AC dies as do the cooling fans behind the radiator (which I do not know until I get to where we're going and the car begins to overheat sitting at a traffic light. My wife goes in and delivers the packages and I try to figure out what's going on. I let the car cool off and add some distilled water (which I happen to have in the trunk at all times). I see that the fuse to the AC has blown and I happen to have a replacement which I put in. Then I see that the Electrolyzer does not come on when I turn the key in the ignition. I check it's fuse and it is not blown. At the moment it's looking like the AC relay may be dead, but I cannot figure out the cause. Is it all unrelated stuff, or have I done something really wrong? At the moment I simply do not know. The most recent adjustments that I've made to the system are these: I added another half teaspoon of Baking Soda to the water bring my content up to 2 teaspoons; the new Electrolyzer tower is notched every quarter inch and the windings have increased accordingly; I removed the check valve from the vacuum line going to the manifold, and I plugged the other vacuum line with a bolt so that it no longer connects to the air filter housing. That's it - the only thing electrical in all of that - is the Baking Soda. Seems like I'm grasping at straws. Is it possible that even though the original MAP Sensor has been replaced with a new one - could the new one be equally goofed but in a different way? Dunno. I'm going to copy/paste all of the above onto the w4g forum and see if anyone of the mucky-mucks can figure out what's up. Once I have an answer I will post back here.

On another subject I want to pass along something that was kindly passed to me by a friend of mine - Henry in Taiwan (hello Henry:-), I think that nearly everyone will find it very interesting. It on the subject of Oxygen Sensors... copy/paste begins Henry,
There are a few things you can do with the O2 sensors once you've put in the DEMSE. Remember, only mess with the O2 sensor(s) before the catalytic converter, not the one(s) after.

1. Leave the O2 sensors alone. This will probably not work. Usually, when faced with an 'enhanced' signal from the MAP sensor, the ECU will apparently ignore it and only look at the O2 sensor input.

2. Try one of the O2 sensor enhancers -
a) foil wrapping - I have not seen this work for many people.
b) O2 extenders/oxyisolators - I also have not seen this work for many.
c) EFIE - you can adjust the O2 sensor output. This is rather pricey, but works.

3. Disconnect the O2 sensors before the catalytic converter. This is what Ozzie does. Make sure you wrap the disconnected plugs so they don't get damaged. This is the way to go, if you're going to have a MAP sensor enhancer. The ECU will not be able to look at the O2 sensor signal, because there isn't one - it is forced to take the ECU signal. Your Check Engine light will go on, but you'll be prepared for it. Just ignore it.

Happy Mileage!
JJ Ferretti
Tech Support copy/paste ends

Now I gotta say - I have the spacer on my sensor and I cannot really tell if it's doing anything or not - but I am opting for the Number three solution. If it's good enough for Ozzie - it's good enough for me.

New Video - How to Wrap the Wires

So many of you have sent me messages of thanks for the other video on the same subject, so I do understand that it was helpful, and I'm really happy about that. I do however think that this one should be all the more useful since, thanks to my son Josh, my hands remain on the screen at all times.-)

Obviously this one is concentrated on wrapping the tower with 1/4 inch notching, but the principle remains the same for any one of them.

I've also realized that I might make things easier if I include links here to the other two videos that relate to assembling the two parts of the tower and the original one on wrapping the electrode wires onto a tower...

Latest Mileage and Other Interesting Stuff

Well it's been a busy week and I'm finally getting around to updating my progress, and I want to state for the record - that it is indeed progress. Oh sure I've been boohooing about how I want consistency and high numbers and it finally got through to me that, at this point, I am getting the consistency part of the equation - 23.3 is a consistent gain of 2 extra miles that I'm getting from each gallon of gas. Correct - it's not huge, but it is after all there.

So what's missing? I have the MAP Enhancer doing it's job; the Oxygen Spacer is in place, a new Electrolyzer has been added. I've been told that adding more baking soda is the next step to take (short of putting in a second Electrolyzer) in getting more HHO from my single unit. Other people warn me that if I use too much baking soda I might melt the tower. - To address that issue at least: one thing is easy to look up online, and that is the melting temperature of Plexiglas. That process happens at 270 degrees Fahrenheit. If I begin to generate that kind of temperature there's one thing that will happen long before the Plexiglas melts: all the water would boil away. Clearly, the melting of the plastic is not an issue. I just added another half teaspoon. We'll see what happens. Also it has been suggested to me that the check valve in my line going to the manifold could be removed to allow a greater flow of HHO. I do have a four foot vacuum line there so I'm pretty clear that there's no danger of getting a spark kicked back into the Electrolyzer, but I'm gong to ask around some more to make very sure about that before I do it. It does make a certain kind of sense after all, but my wife would be pretty angry with me if I blew up the car.-)

There are all kinds of people now letting their creative juices flow - making all kinds of new units. Some of them are pretty interesting - composed of rods and plates, some are larger, and are constructed of new materials. Some are touted as more powerful (and maybe they are), but the one thing that I know for sure is that the original technology, as described in great detail complete with do-it-yourself plans - works. This is where we all must begin to gain a greater understanding of what it is we're dealing with. Harnessing it and playing with it and experimenting with it are exactly the kinds of things that need to be done to lead us all to the next step. Not so many months ago if someone had asked me if water could be ignited I would have laughed at the ridiculous nature of the question. Now that concept is the source of the name of my website. It is the nature of the device that I have added to my car that is without question improving my mileage. The idea that water can, and does, burn is now an obvious truth.

This ongoing exploration and expansion of our technology (something that should have been done over the last 50 years by large automakers), is taking us into a world that has been described by one of my new friends in the water4gas community, Stephanie, as a Silent Storm. We are that storm. We are, as a community of seekers, individually extracting ourselves, our friends, our neighbors, and ultimately our customers from the clutches of Big Oil. Not all at once but a step at a time. Many of us are looking to have this happen within an underlying framework of integrity. Treating one another as fellow travelers rather than competitors we will change more than just the way we fuel our automobiles. We could change the world. It is possible. Certainly as possible as burning water. We are not large corporate entities who have no responsibility to any but their stockholders. We are just people who care about what happens to others. If we each adhere to the truth, as we know it, and keep telling it as long as we know it, and continue to explore how what we're doing can transform the planet into what it was meant to be all all along - we will certainly find that we are doing exactly the right thing at exactly the right moment in time.

To misquote Lao Tzu for my own purposes, "Every journey begins with a single step." Well my friends I believe that we have taken it.

How to Install the MAP Sensor Enhancer

In the past I have asked the same question and it was answered for me by Mr. Minton. Now a man named Eric has asked the question of me and I promised to post the following information here. I am placing a copy/paste of Mr. Minton's instructions to me - as well as a diagram that I created and he kindly corrected for me: copy/paste begins - There are three wires coming out of the MAP Sensor. One is the Ground, one is the 5 volt Sensor Power, and the third is the MAP Sensor Signal to the Car's computer, the ECM. You cut the third wire and splice each end to the MAP Sensor Enhancer according to your instructions.

There are three wires coming out of the MAP Sensor Enhancer. One is Black; connect this to a wire that is attached to your cars frame or similar location. The other two wires are spliced onto the two ends of your MAP Sensor. The Red wire connects to the MAP Sensor signal wire and the Brown wire connects to the wire going to the ECU. When connecting the Enhancer be sure the dials are set to "0". Once you have it installed, turn the lower switch to "Enhanced" and the upper switch to "City". Then slowly turn the "City" dial until your engine starts to sputter, then turn the dial back 1/4 turn.

The following website http://www.hhodevelopment.com/introsupport.htm will explain everything you need to know about the installation. Also, you will need to add an Oxygen Sensor Extender to your O2 Sensor. If you have duel exhausts, you will need two. Your O2 Sensor is located on your exhaust manifold before the catalytic converter. - copy/paste ends

If anyone else has anything to add or subtract from this please do so as a comment for everyone to see and benefit from.

Changed Out the Original Electrolyzer

As you can see I've laid these two towers side by side to compare the differences. Naturally, the one on the right is the one that I built and wrapped, and this photo was taken before I installed it in the car. So it's obvious that it is perfectly clean and has no residue on it. The other - is the one that's been in my car for a bit longer than a month and yes it's nasty looking, but more than that - now that I know what I'm actually looking at: there are very few winds of the electrode wire and worse than that I notice that the negative wire is beginning to rust! This means that this wire is not 316L stainless steel. This means that what I've had sort of working in my car was not made properly and was not made using quality materials. I will not divulge the name of the person who sold it to me, rather I will simply encourage everyone to use the best materials and to treat others in the water4gas community as though they were members of your family. This is not only about the integrity of the product - it is also about allowing people to have the best possible experience as they begin to explore this technology. Let's not discourage others through a greater desire to make money than to have people know that this really works.

When my MAP Sensor Enhancer was not working I could not know until Mr Minton informed me of what had happened. The reality that my electrolyzer in all probability has never worked properly is something I had to discover for myself. If I were not moving along in my quest for understanding I might not have made the discovery. I might have gotten discouraged and even given up never knowing that I was so close.

Anyway the new electolyzer is in the car. All of the areas where it might leak (sucking air through the lid or around the electrical posts) have been carefully sealed. I switched out the universal vacuum fitting for a fitting that exactly fits my hoses. The one thing that I've not yet figured out is how much baking soda to use in the electrolyzer with so many more windings. I will find out and report back here.

One other thing: As soon as I put the new Electrolyzer I went ahead and refilled the tank so that I'd be getting a more accurate measurement for the next posting. It amount that I put in was insignificant and I did not recored that mileage.

Also I just put up the new website www.ignitingwater.com where I am selling support products for water4gas.