Saturday, June 28, 2008

Mileage report with the new Enhancer

I'm in that spot again. I want to talk about the incredibly great mileage that I'm getting now that I have placed all of my ducks in a row, however I can't do it! Sure, 23.6 MPG is better than I was doing, but let's face it - I've seen 26. I want 26 again. I want 40!

As most of you must know by now I am fairly persistent, and I'll not let this go until I get what I want. There are certainly enough of you now encouraging me, and telling me that it is possible. Telling me about your Toyota getting mileage that I only dream about. - Thanks a lot. No really, all kidding aside - thank you all.

My thought as I sit here writing this is that I'll go back to the Electrolyzer and put in a new tower with my own windings on it - In the last day I've started producing and selling 1/4" thick towers with notches at the 1/4" so there are nearly twice as many windings apparently producing twice as much HHO so that my car can run leaner. (Thanks to Rod and Steph for cluing me into new info from Ozzie) I expect that I'll have time to do that on Monday.

I feel that I should mention this: The Electrolyzer that I have on my car is not one of the one's that I've made. Rather it is the original one that I bought as a completed item (it has glue on the coils which is obviously something I personally identified as a problem. "Why then," you ask with a look of stunned amazement at my stupidity, "didn't you put one of your own creations on?" - It's a damned good question. I suppose the only real answer is - that I got caught up in the fact that it has worked in the past, and I've been busy: the sales of the towers have taken up a surprising amount of time. More to the point - it didn't occur to me that it might not be delivering the amount of HHO that my car actually needs. (Although that leaves me wondering why it did what it did in the first place.) Nevertheless, I'm now about to remedy that situation.

The way things stand at the moment is that I am in the midst of an experiment, and as it happens I am one of the factors in that experiment. I may well have done something wrong (though I have no idea what) - it might not be my influence at all. I will find out and hopefully this excursion of mine will assist the rest of you.

So one more time I've taken another step. At least it's not a step backward as some others have been, and it's even a slight move forward. Bottom line: I want a giant step forward. Don't we all?

Also I want to add a quick note about the towers: one of my clients let me know that when he was wrapping the electrode wires on one of the 1/8" thick versions he cracked it in half. This is the first and only incidence of this that I know about. I have replaced it with a 1/4" version at my expense. All I can say is that I have personally wrapped about 20 of these things without problem and I expect that it may be as simple as my having a lighter touch. In the last day I've also replaced one of the 1/4" towers - it broke in the mail. What the Post office needed to do to make that happen is almost beyond belief. I guess that I'm just saying that things happen and I will always stand behind my products. If you think that you might be very strong or just want to wrap wires really tight - go for the 1/4" towers.

See you next time I fill up - or before if I think of something really profound to say. - Yeah right.

One last thing waterxfuel is soon to become ingitingwater. Watch for it.

Tuesday, June 24, 2008

I just put the new MAP Enhancer in.

The wait is over and I've got the new Enhancer in place. I asked for and received the following instruction on how to set up the City side of the Enhancer: When connecting the Enhancer be sure the dials are set to "0". Once you have it installed, turn the lower switch to "Enhanced" and the upper switch to "City". Then slowly turn the "City" dial until your engine starts to sputter, then turn the dial back 1/4 turn. I expect that this will come in handy for anyone going down this path.

ADDED NEXT DAY: I also asked for and received the following information on how to set the Highway side of the Enhancer:
The Highway setting is for speeds above 40 mph. Match the HWY Dial to your City setting. After reaching a speed of 40 mph, switch to your dial to HWY and lean it out until your comfortable with your setting. Be careful and do this slowly. You don't want your engine to die at that speed. Also remember, when you want to pass or go up a steep incline, switch your lower switch to Factory so you will have all the power you need. Good info for all.

As I said in the last post I waited to fill up until I got the new gadget, so here are the results - as you can see I didn't do as badly as I'd expected since this works out to 22.9 MPG - (lets call it 23 why don't we) which is nearly couple of miles-per beyond my norm. This was obtained with the Oxygen Sensor Spacer installed as well as the HHO Generator. I suppose if I'd done the battery trick I would have done even better. It just occurred to me, (as I wrote that last line) that I didn't do it when I did the install - so I promise to go out and do it in a little while so that everything starts from an even base.

Wish me luck since my luck will also be yours...

Monday, June 23, 2008

Waiting waiting waiting

Today I waited all day long to receive my replacement MAP Enhancer. The Post Office taunts me with their insane tracking method which lets me know that it has arrived in the local station. Yet, I still do not have it! (See me thrumming my fingers on the desk.) Tomorrow is the day. (One can only hope.) Once I have it installed I'll put gas in my half full tank and report the results of having the Electrolyzer and the Oxygen Sensor Spacer in place. My hopes are not high. I did not bother to reset the computer with the disconnect the battery trick. Figured to do that when I put in the new Enhancer. On the other hand, one of my clients gave me new trick (you know who you are but I've forgotten - please write in as a comment to identify yourself - and I'll inform the readers of your ability to provide awesome information). Instead of pulling the the negative cable and leaving it off for 20 to 30 minutes - pull both cables off and touch them together. Reportedly it will do the same reset without the wait. Now, that's great... Thanks to that guy from all of us...

Thursday, June 19, 2008

On the Subject of Brittle Wires

I've received several calls from people who are having a problem with the electrode wires that they are twisting up for themselves (not those that I sell) snapping while they're attempting to twist them up with a drill. Personally, I have not had this experience, but from what I've gathered from those discussions is that some 316L wire is somehow impregnated with silicone and has the designation 316Lsi. I would advise against that purchase since it seems to be at the heart of the problem. The wire that I use comes from a company called McMaster-Barr (link provided) and these are the specs that you want when ordering:
Material Super Corrosion-Resistant Stainless Steel (Type 316/316L)
Finish/Coating Matte
Shape Wire
Wire Type Standard
Diameter .032"
Tolerance Standard
System of Measurement Inch
Material Certification Without Material Certification
Gauge 20 AWG
Specifications Met Not Rated
I encourage anyone who wishes to do so to order from them and twist up your own wires. For those of you who do not want to deal with that - as you may know by now - I sell the complete pre-cut and twisted wire sets for $6.50 [additional info added 7/6/08: for the 30 inch sets and $15.00 for the 60 inch sets] which I see as a very reasonable price for the service.
It's all good.

Wednesday, June 18, 2008

How to Wrap the Electrode Wires


So yeah. I know that my hands drift out of the screen a few times, but I think that the video is good enough for the time being. I promise to redo it - soon. In the meanwhile please use it and see if it doesn't help you to figure this process out. Personally, I believe in a hands on approach and everyone would best be served by grabbing up a tower and going for it. The worst that could possibly happen would be that you'd do it wrong and have to start over again.

What follows is a copy/paste of a text description of wrapping the electrode wires that I wrote out for one of my clients: at the top of the assembled tower run the first wire through one of the holes there. Do this from the top down so that the looped end (to be attached to the electrode post) is at the top with enough room to make the connection to the post. Begin wrapping the wire - beginning by dropping down a couple of notches. Continue to wrap - skipping every other notch until you reach the bottom where you will push the end of that wire into one of the holes there - and give it a good bend to keep it in place. Repeat the process with the other wire - in the opposite hole on the top and placing it into the notches that you skipped before.. Just remember you're winding in the same direction as the first wire.

Hopefully, between the video (even flawed as it is) and the description you'll find this part of the process relatively easy.

Everyone please feel free to comment, ask questions or make suggestions. - you know the rules:-)

Tuesday, June 17, 2008

How to assemble the two parts of the tower.




Several people who've purchased the uniquely designed electrolyzer towers from me - have asked how to put the two pieces together, so I've cooked up a little flick (very short) to show just how it's done. When I have a few moments to produce my next extravaganza - I will also upload a video demonstrating how to properly lay in the electrode wires. I hope that this is helpful.

Anyone interested in purchasing towers can just look over at the the sidebar on the right of this blog to see how to do that. Or just write to me at waterxfuel@gmail.com with: how many you want - the thickness you want (1/8 or 1/4 inch) - and the state you live in.

The Mystery May Well Be Solved

So I did find that air leak but it really seemed to me to be a rather insignificant leak - still I was grasping at straws. I just knew that I had to have done something wrong. Well as it turns out it wasn't me at all. The MAP Enhancer that I bought from Vernon Minton was faulty, and the fact is that if he'd not written to tell me about it I never would have known:
Dear Mr. Ellis
The MAP Enhancer we delivered to you may have one or more defective parts. Please ship this unit back to us at: [Address deleted by Jon]
After removing the unit from your system, be sure to reconnect the MAP Sensor Signal wires. If you have a HHO Generator installed, remove the fuse until you re-install your MAP Enhancer.
After we receive the unit, we will immediately priority mail you a new one and credit your PayPal account for the shipping.
We apologize for this inconvenience. If you have any questions, please use this email address.
Thanks,
Vernon F Minton
Once again Mr. Minton has demonstrated his integrity and I for one appreciate it. It would have taken me forever and a day to figure out that something was wrong with the Enhancer. Sure it 's a hassle but such thing happen with computer and TV and what-all, and I've never once had a note from Sony telling me that there was a problem with something that they sold me and that they wanted to make it right. If I found something wrong it's always been up to me to discover it and then go through the maze of telephone robots to get satisfaction.
Rock on Vernon!

Monday, June 16, 2008

I hate to say this, but...

As I've mentioned before I do feel a desire to lie at times like these. I want this to work. When it does work I'm totally jazzed about it. I don't want to report that I'm having a problem. I want to inflate the figures so that this technology will appear to be working better than the results that I am currently experiencing would indicate, but I'm not going to do it! The reality is what it is. As you can see I got approximately 19.6 MPG. Again this is less than I get with no enhancement of any kind. Am I frustrated? YES! Will I give up? No because the fact is that I've seen it work with my own eyes and I expect to see it again. Clearly, I'm doing something wrong and I will get the information that I need to do it right. I happen to be a very persistent person.

In the light of the above I've posted the following in the W4G forum: Ok now I'm totally baffled. I have the MAP Enhancer installed, and can actually hear the difference when switching between "Factory" and "Enhanced." I have a spacer in the upstream Oxygen sensor. I've reduced the amount of baking soda in the electrolyzer to 3/4 tsp. I've made sure that my vacuum lines are as open as possible (cut back the "T's" and reamed them out) - And my mileage is back to 19 MPG! Remember that without any H.H.O. device I was getting 21 MPG... I don't mind being the guinea pig, but I'm actually wasting fuel at a time when that should be considered to be a sin.

I will post the answers here and I will peruse any viable solution and post those results as well. BTW - I filled the tank before hitting the highway yesterday and the round trip was 22.6 miles. At this point I don't know if there was a gain of any kind, but I just thought I'd let you know that that mileage will be included when I post the next results.

UPDATE (a few hours later): I just received this answer to my query:
I hope you don't mind me putting in my $0.27 (inflation). I've followed your posts and you see saw mpg's and frankly, I'm (almost) baffled also. The almost is the reason for this letter. That and the fact that I agree about wasting gas should almost be a crime. Of course, some experimentation is justifyable.

So, the thing is, I have posted about the lids on the H.H.O. units not sealing well, and was wondering if you have checked for this problem?
Remember, though they might have sealed when installed, the plastic lid has a tendancy to warp with heat. I use a water-proof silicone, "Form-A-Gasket", as I feel that it is flexible enough to "warp" with the lid.
As you know, excess air leaking into the jar would have the same effect as a leaky vacuum line, causing a loss of performance and lower mpg.

I so appreciate this guy - a really forthcoming person who is willing to share what he knows. So I just checked my electrolyzer for leaks and what do you know I found one! I am going to take care of that but I do wonder just a bit if it's so much more air leaking in than the bubbler delivers (which admittedly isn't much). We shall see. I continue to wait for other possible answers...


Saturday, June 14, 2008

And Now For Something Different

The conversation below is a direct Copy/Paste from my email. I figure what the heck. Everyone makes their own decisions based on how they feel anyway. So make your own decisions. Everyone is welcome to comment. Please keep it relevant and relatively clean. - Jon

CHRIS:
I just wanted to mention that I read and enjoyed the entire blog that you posted (well most of it lol it is very extensive). I noticed that you have for sale the Plexiglas towers and I was wondering if you build them or are advertising for someone else. I actually manufacture the MAP Sensor Enhancers and sell them on eBay and now I am creating my own website. I was wondering if you would be interested in somehow linking to me or even putting a picture of mine on there or something? Basically I would like to work out some kind of deal where I can sell my MAP Sensor Enhancers on your site. I am not a big corporation just a hometown guy with a passion for electronics. I have been into the HHO stuff for a while and the MAP Sensor Enhancers have helped fund my business. Anyway let me know if you may be interested and regardless I will keep reading your blog.

Thanks, ~Chris

JON: I really do appreciate your kind words, but the fact is that I do not know you, nor can I vouch for the quality of your work or your personal integrity. And I am not in the business of advertising for others. Rather I am attempting to create a base of real information about something that, on the surface anyway, has every appearance of some kind of a scam. You an I know that this is not the case, but if I begin to post ads for others I'm afraid that it might skew my credibility. You do however sound exactly as if you are what you say you are. Meaning that you sound OK to me - and I'd like to support your efforts... Tell you what I will do, for the time being anyway, is this : I am willing to post a copy/paste of both sides of this conversation into the Water4Gas Report. Also, pass me the link to your website and give me permission to post your email address and I will put them up. Send along a photo if you like. What will happen after that is that I'll tag our conversation including your name and site name and invite others to post their experience with you. If that sounds fair just reply to this email with the information. Once I've received your email I will copy everything and post it.

In answer to your question - I personally designed these towers, cut the original prototypes, and have contracted directly with a friend of mine - who is the manufacturer.

Cordially,
Jon

CHRIS: That sounds great to me. I appreciate the help. My website is http://gvec.net/dbitsis/ and it is under construction sort of as I have just started it. It should mostly be there and I will be adding to it everyday. If you personally ever need to buy any MAP sensor enhancers or anything else I will be selling then we can definitely work out a deal. Attached is a picture that you can put somewhere if you would like. Again I thank you for the help as I am trying to get off the ground and off of ebay because it seems unfair the amount of fees they take from me. My name is really Daniel Bitsis, I just go by my middle name Chris since I am a junior.

Thanks, ~Chris

Friday, June 13, 2008

About That Oxygen Sensor Spacer

Yesterday I made a valiant effort to install the thing and only managed to scrape my knuckles badly enough that they still hurt. It turns out that (at least for my car) you need a special wrench to pull the sensor out. My friend (and mechanic), Louie lent me the tool but the results were as stated above. Today I went back over to his shop and asked him to do the task for me - which he did in quick order and refused to accept payment. It took him all of 10 minutes. Experience and having the correct tool - counts.

So as you know I'd already put in the MAP Enhancer. So as a consequence of my failed attempt at installation - I'd already driven 29.4 miles - when the spacer was actually installed. So - I did drive around a bit with that piece of the puzzle missing, but also felt that I was getting a true gain that would show up with the spacer in or not. What happened next was unexpected but it was something that I noticed immediately upon driving out of Louie's shop: my MAP Enhancer needed to be readjusted to a leaner mixture. There was no doubt that something different was going on. It was unmistakable.

My next posting will contain my newest mileage stats, and for the first time they will reflect some highway driving. We intend to take the kayaks out for a spin tomorrow and will need to get to some interesting location - right? At least something more pristine than the East River.

Thursday, June 12, 2008

Worst Mileage Ever

That's right this works out to 17.7 MPG. I got 4 miles less per gallon than my car gets all on its own! The reasons are clear and they all come back to me: As I posted earlier I could see that the car was not doing as well as it should - but did I disconnect the negative terminal from the battery for half an hour to let the computer reset again? Nope - I didn't want to deal with having to reset the radio stations and the clock. OMG did that lazy attitude come back to bite me in the behind - especially when I just paid more per gallon than ever. Also, I was waiting for the overwhelming heat to go away so that I could install the MAP Sensor Enhancer, so I didn't go in to fill the tank until that was done - meaning that I paid more and and at the same time had to buy more. Sure I knew the cost of gas was going up - because these days it's always going up. All in all - painful.

On the other hand, I did get the Enhancer installed yesterday. Just to be on the safe side of getting things in order, while I did the installation I did disconnect the battery. There was some mention in the instructions that I got of disconnecting the upstream Oxygen sensor - but I couldn't figure out how to do that other than pulling the electrical line off - which amounts to the same thing. Reason: I want to put the spacer on and I'm waiting until I talk to my mechanic to see if he can tell me how to do that without wrecking it. (I'll report later on that.)

What I did do was get the MAP Enhancer online and working! As you might surmise - I am fairly well proud of myself. Choosing the correct wire seemed a real problem but once I got it - I got it. I can tell that it's doing what it's supposed to do by a very simple test. First I followed the directions for tuning it and found that spot for my car that works best. Then, while the car was sitting at an idle I flicked the setting from Enhanced to Factory. There is a very noticeable difference in the engine. It is unmistakable. I did it right. I expect that that difference will show up the next time I fill up ( and I won't be waiting so long until I do that - because I'm dying to see the results). It's all I can do to keep myself from just going out and driving around, but I'm really not all that willing to demonstrate how stupid I can be:-)

Another thing that I did while I was installing the Enhancer is that I took another look at the "T" connection for the vacuum lines connected to the Electrolyzer - I noticed that one of them appeared to be loose. It was - which certainly may be responsible for the terrible mileage. I just don't know. Still, I took a close look and realized that the Universal T is designed in a way that each end narrows further and further so that it can accept all sizes of lines. What this means is that for my car I had lines that didn't need to be as small at the ends as these were - so I cut them off with wire cutter and reamed them clean with an Exact-o blade. What this should mean is that I will get more vacuum pulling the HHO into the manifold.

I'm realizing more and more that each little thing is important. As always I'm learning at each step and with any luck you will be able to avoid the pitfalls through my missteps.

Tuesday, June 10, 2008

I'm getting to it...

The fact is that even though I have the equipment I don't have a place in the shade to work in and sad but true the heat is too much to deal with. Out in it for ten minutes and literally felt nauseous! Generally I love the heat, but this is beyond anything. They say that it'll cool down later tonight, so tomorrow looks like the install day. Looked in the package and realized that I'd only ordered 1 Oxygen Sensor Spacer even though I knew I needed 2! Rats. I have the other one on order. I will install the one I have along with putting in the MAP Enhancer. Once I have those on the car I'll go put gas in it and I can tell that I've been wasting gas on this run. Hopefully my mistakes and falters will help the rest of you to avoid those things... Maybe not. Anyway, I'll report again as soon as I get things in order.

Saturday, June 7, 2008

And on... and on...

Well, I haven't filled up yet but I can make a pretty good guess that the mileage is not where I want it to be. I do have the MAP Sensor Enhancer in my possession and have spent several days looking at it (it's just my style to do it this way) and rounding up information on how to install it properly. I would have put it on today, but frankly it was just too damned hot out there ( a humid 96 degrees). Maybe tomorrow. Also, I have a couple of Oxygen sensor spacers coming in a day or so (hopefully Monday). Once I've installed everything I'll come back and reveal the mileage from this fill up and will zero out to be ready for the next one... The next one should be the real deal.

By the way I ordered my MAP Enhancer from a guy named Vernon Minton. The link on his name will take you to his website. I wanted to mention that there are people out there who might sell you one of these gadgets for a little less, but this is a guy who went the extra mile to help me to understand how to hook the darned thing up. Certainly a person worth knowing. His work, by the way, has every appearance and feel of the highest quality. Highly recommended.

I'll be back.

Tuesday, June 3, 2008

Did it Again!

It's a fact! I was able to duplicate my first results which of course lead me to be so persistent in trying to work this technology out. As you can see I traveled 89.4 miles on 3.51 gallons of gas which means I got 25.47 MPG but it's even better than it looks because the last 2 miles or so I was in lots of stand-still traffic in Manhattan and I had the AC on. On top of that the car sat idling (again with the AC on) when some bozo ran into me and tried to drive off. (Everybody's fine) Well, the cops stopped him and I had to fill out all the usual rigmarole papers and blah-blah-blah. Why you ask was the car idling with the AC on? My lovely and beautiful wife Georgina was with me, and she needed it. 'Nuff said?

Anyway this is a real victory. What I want to see now is a consistent gain each and every time. That means that I need to put the MAP sensor on and figure out the oxygen sensor... There is a complexity to this, but I notice that once I get past my hesitation at doing something new - it becomes easy and natural.

If you want to check this technology out for yourself - this is the link

Yes, I do make money when you use the link to buy the books, but I would not encourage you to buy them unless I felt good about the product. Up until now I've felt good about it. Now, I feel great about it.

I encourage anyone to buy the books - buy the parts and begin your own local green revolution. I expect that as time goes on I will figure out how to do even better. I will begin to understand the technology in ways that I've not reached yet. My goals? The same as yours: to be free from Big Oil, to live on a healthy planet, to create a better future for my children.